Коды ошибок Konica Minolta Bizhub C224/284/364 (C1141 - C1182)

Список включает ошибки моделей C224/284/364 и C224e/284e/364e 

 

  • Code: C1141

Description:

Paddle motor’s drive malfunction

<When FS-534 is installed>

The upper paddle homeposition detection sensor (PS14) is not blocked or unblocked even after the set period of time has elapsed while the FNS paddle motor (M5) is turning.

Remedy:

  1. Check the connector between M5-FSCB J4 for proper connection, and correct as necessary. 
  2. Check the connector of M5 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS14-FSCB J4 for proper connection, and correct as necessary.
  4. PS14 I/O check, sensor check FSCB J4<B>-7 (ON) FS-534 13-C.
  5. M5 operation check FSCB J4<A>-5 to 8 FS-534 12-C to D.
  6. Replace M5.
  7. Replace FSCB.

 

  • Code: C1144

Description:

Pre-eject drive motor’s malfunction

<When FS-534 is installed>

• The pre-eject home sensor (PS21) is not blocked or unblocked even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON.

• The pre-eject away sensor (PS22) is not blocked or unblocked even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON.

Remedy:

  1. Check the connector between M9-relay CN7<A>- FSCB J13 for proper connection, and correct as necessary.
  2. Check the connector of M9 for proper drive coupling, and correct as necessary.
  3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary.
  4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary.
  5. PS21 I/O check, sensor check FSCB J12-6 (ON) FS-534 6-C.
  6. PS22 I/O check, sensor check FSCB J12-9 (ON) FS-534 6-C.
  7. M9 operation check FSCB J13-3 to 4 FS-534 8-C to D.
  8. Replace M9.
  9. Replace FSCB.

 

  • Code: C1145

Description:

Trailing edge stopper motor’s malfunction

<When FS-534 is installed>

The trailing edge stopper home position detection sensor (PS20) is not blocked or unblocked even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON.

Remedy:

  1. Check the connector between M6-FSCB J5 for proper connection, and correct as necessary.
  2. Check the connector of M6 for proper drive coupling, and correct as necessary.
  3. Check the connector between PS20-relay CN22-FSCB J5 for proper connection, and correct as necessary.
  4. PS20 I/O check, sensor check FSCB J5-9 (ON) FS-534 9-K.
  5. M6 operation check FSCB J5-13 to 16 FS-534 9-K.
  6. Replace M6.
  7. Replace FSCB.

 

  • Code: C1156

Description:

Center-staple paddle roller motor malfunction (trailing edge)

<When FS-534+SD-511 is installed>

The paddle home sensor (PS5) is not blocked or unblocked even after the set period of time has elapsed while the SD paddle motor (M7) is energized.

Remedy:

  1. Check the connector between M7-SDDB J8 for proper connection and correct as necessary. 
  2. Check the connector of M7 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS5-SDDB J8 for proper connection and correct as necessary. 
  4. PS5 I/O check, sensor check SDDB J8-3 (ON) SD-511 3 to 4-G. 
  5. M7 operation check SDDB J8 4 to 7 SD-511 3-F to G. 
  6. Replace M7. 
  7. Replace SDDB. 
  8. Replace FSCB.

 

  • Code: C1182

Description:

Shift motor drive malfunction

<When JS-506 is installed>

• The tray shift home sensor (PS1) is not unblocked after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the home position.)

• The tray shift home sensor (PS1) is not blocked after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the shift position.)

Remedy:

  1. Check the connector between M1-JSCB CN208 for proper connection and correct as necessary.
  2. Check the connector of M1 for proper drive coupling, and correct as necessary. 
  3. heck the connector between PS1-JSCB CN208 for proper connection and correct as necessary.
  4. PS1 I/O check, sensor check JSCB CN208-5 (ON) JS-506 5-C. 
  5. M1 operation check JSCB CN208 1 (DRV) JS-506 4 to 5-C. 
  6. Replace M1. 
  7. JSCB ICP3 conduction check. 
  8. Replace JSCB.