Коды ошибок Konica Minolta Bizhub C224/284/364 (C1102 - C1140)

Список включает ошибки моделей C224/284/364 и C224e/284e/364e 

 

  • Code: C1102

Description:

Main tray up/down motor’s drive malfunction

<When FS-533 is installed>

• While the exit tray is being lifted, the stapler movement motor (M107) is not unblocked after the set period of time has elapsed after the tray lift up motor (M109) is turned ON.

• While the exit tray is being lowered, the stapler movement motor (M107) is not blocked after the set period of time has elapsed after the tray lift up motor (M109) is turned ON
<When FS-534 is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not blocked and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times.

• While the exit tray is being lowered, the main tray full detection sensor (PS29) is not blocked after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON.

Remedy:

When FS-533 is installed:

  1. Check the connector between M109-FSCB CN108 for proper connection and correct as necessary. 
  2. Check the connector of M109 for proper drive coupling and correct as necessary.
  3. Check the connector between PS107-FSCB CN110 for proper connection and correct as necessary.
  4. PS107 I/O check, sensor check FSCB CN110 FS-533 7-D to E.
  5. M109 operation check FSCB CN108 FS-533 10-E.
  6. Replace M109.
  7. FSCB CP109 conduction check.
  8. Replace FSCB.

When FS-534 is installed: 

  1. Check the motor and sensor connectors for proper connection, and correct as necessary. 
  2. Check the connector of M11 for proper drive coupling, and correct as necessary. 
  3. PS26 I/O check, sensor check FSCB J14<A>-5 (ON) FS-534 2-C. 
  4. PS27 I/O check, sensor check FSCB J14<B>-8 (ON) FS-534 3-C.
  5. 5 PS29 I/O check, sensor check FSCB J14<A>-8 (ON) FS-534 4-C. 
  6. SW2 operation check. 
  7. M11 operation check FSCB J9<A>-9 to 10 FS-534 10-C to D. 
  8. Replace M11. 
  9. Replace FSCB.

 

  • Code: C1103

Description:

Alignment plate motor/Fr’s malfunction


<When FS-533 is installed>

• The alignment plate home sensor/F (PS108) is not unblocked after the set period of time has elapsed after the plate drive starts from the home position.

• The alignment plate home sensor/F (PS108) is not blocked after the set period of time has elapsed after the alignment motor/F (M105) is turned ON to return the plate to the home position.


<When FS-534 is installed>

• The alignment plate/F home sensor (PS12) is not unblocked after the set period of time has elapsed after the plate drive starts from the home position.

• The alignment plate/F home sensor (PS12) is not blocked after the set period of time has elapsed after the alignment motor/front (M7) is turned ON to return the plate to the home position.

• The alignment plate/F does not reach the specified position within the set period of time

Remedy:

When FS-533 is installed: 

  1. Check the connector between M105-FSCB CN102 for proper connection and correct as necessary. 
  2. Check the connector of M105 for proper drive coupling and correct as necessary. 
  3. Check the connector between PS108-FSCB CN102 for proper connection and correct as necessary.
  4. PS108 I/O check, sensor check FSCB CN102 FS-533 7-J. 
  5. M105 operation check FSCB CN102 FS-533 7-J. 
  6. Replace M105. 
  7. FSCB CP105 conduction check. 
  8. Replace FSCB.

When FS-534 is installed:

  1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary.
  2. Check the connector of M7 for proper drive coupling, and correct as necessary.
  3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 
  4. PS12 I/O check, sensor check FSCB J4<B>-4 (ON) FS-534 13-C. 
  5. M7 operation check FSCB J4<A>-5 to 8 FS-534 11-C to D. 
  6. Replace M7. 
  7. Replace FSCB.

 

  • Code: C1105

Description:

Bundle eject motor’s drive malfunction


<When FS-534 is installed>

• The gripper home position sensor (PS18) does not block even after the set period of time has elapsed after the gripper position detection sensor (PS19) unblocked.

• The gripper position detection sensor (PS19) does not block even after the set period of time has elapsed after it unblock

• The gripper position detection sensor (PS19) does not block even after the set period of time has elapsed after the gripper home position sensor (PS18) unblocked.

• The gripper home position sensor (PS18) does not block even after the set period of time has elapsed after the bundle eject motor (M10) unblocked.

• The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) are blocked at the same time.

Remedy:

  1. Check the motor and sensor connectors for proper connection, and correct as necessary. 
  2. Check the connector of M10 for proper drive coupling, and correct as necessary.
  3. PS18 I/O check, sensor check FSCB J13-13 (ON) FS-534 7-C.
  4. PS19 I/O check, sensor check FSCB J12-3 (ON) FS-534 7-C.
  5. M10 operation check FSCB J13-1 to 2 FS-534 8-C to D.
  6. Replace M10.
  7. Replace FSCB.

 

  • Code: C1106

Description:

Stapler movement motor’s malfunction

<When FS-533 is installed>

• The stapler home sensor (PS110) is not unblocked after the laps of given time after it started operating from the home position.

• The stapler home sensor (PS110) is not unblocked after the laps of give time after the stapler movement motor (M107) turned ON when it returned to the home position.


<When FS-534 is installed>

• The stapler home position sensor (Rear) (PS23) is not blocked or unblocked even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON.

• The stapler does not reach the specified position within the set period of time.

Remedy:

When FS-533 is installed: 

  1. Check the connector between M107-STREYB CN123 for proper connection, and correct as necessary. 
  2. Check the connector of M107 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS110-FSCB CN110 for proper connection, and correct as necessary. 
  4. PS110 I/O check, sensor check FSCB CN110 FS-533 8-D to E. 
  5. M107 operation check STREYB CN123-5 to 8 FS-533 5-L. 
  6. Replace M107. 
  7. Replace STREYB. 
  8. FSCB CP107 conduction check. 
  9. Replace FSCB.

When FS-534 is installed: 

  1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 
  2. Check the connector of M13 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 
  4. PS23 I/O check, sensor check FSCB J11<B>-3 (ON) FS-534 4-C. 
  5. M13 operation check FSCB J11<A>-1 to 4 FS-534 4-C to D. 
  6. Replace M13. 
  7. Replace FSCB.

  • Code: C1109

Description:

Stapler motor’s drive malfunction

<When FS-533 is installed>

The stapler home sensor (PS110) is not blocked even after the set period of time has elapsed after the stapler motor turned ON.

<When FS-534 is installed>

• The stapler home position sensor (Rear) (PS23) is not blocked or unblocked even after the set period of time has elapsed after the stapler motor (M14) turned ON.

• The stapler position sensor (Center) (PS24) is blocked, when the stapler motor (M14) is running.

Remedy:

When FS-533 is installed: 

  1. Check the connector between the stapler unit- STREYB CN122 and CN123 for proper connection and correct as necessary. 
  2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 
  3. Check the connector between PS110-FSCB CN110 for proper connection and correct as necessary. 
  4. PS110 I/O check, sensor check FSCB CN110 FS-533 8-D to E. 
  5. Replace the stapler unit.
  6. Replace STREYB. 
  7. Replace FSCB.

When FS-534 is installed: 

  1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 
  2. Check the connector of the stapler unit for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection and correct as necessary. 
  4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 
  5. PS23 I/O check, sensor check FSCB J11<B>-3 (ON) FS-534 4-C.
  6. PS24 I/O check, sensor check FSCB J11<B>-6 (ON) FS-534 4 to 5-C. 
  7. Replace the stapler unit. 8 Replace FSCB.

 

  • Code: C1112

Description:

Stapler motor’s malfunction

<When FS-534+SD-511 is installed>

• The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized.

• The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON.

Remedy:

  1. Check the connector between the staple unit-SDDB J4 for proper connection and correct as necessary. 
  2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 
  3. Replace the staple unit. 
  4. Replace SDDB. 
  5. Replace FSCB.

 

  • Code: C1113

Description:

Center-staple lead edge stopper motor malfunction

<When FS-534+SD-511 is installed> The stopper home sensor (PS6) is not blocked or unblocked even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON.

Remedy:

  1.  Check the connector between M4-SDDB J10 for proper connection and correct as necessary.
  2. Check the connector of M4 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS6-SDDB J10 for proper connection, and correct as necessary. 
  4. PS6 I/O check, sensor check SDDB J10-5 (ON) SD-511 2-G. 
  5. M4 operation check SDDB J10-6 to 9 SD-511 1 to 2-F to G. 
  6. Replace M4. 
  7. Replace SDDB. 8 Replace FSCB.

 

  • Code: C1114

Description:

Center-staple front adjust drive motor malfunction

<When FS-534+SD-511 is installed>

The alignment home sensor (PS4) is not blocked or unblocked even after the set period of time has elapsed after the alignment motor (M3) is turned ON.

Remedy:

  1.  Check the connector between M3-relay CN10-SDDB J7 for proper connection and correct as necessary.
  2. Check the connector of M3 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS4-relay CN10-SDDB J7 for proper connection, and correct as necessary. 
  4. PS4 I/O check, sensor check SDDB J7-6 (ON) SD-511 6-F. 
  5. M3 operation check SDDB J7 7 to 10 SD-511 5-F to G. 
  6. Replace M3. 
  7. Replace SDDB. 8 Replace FSCB.

 

  • Code: C1115

Description:

Center-staple knife drive motor malfunction

<When FS-534+SD-511 is installed>

The center fold knife home sensor (PS8) is not blocked or unblocked even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON.

Remedy:

  1. Check the connector between M9-SDDB J11 for proper connection and correct as necessary. 
  2. Check the connector of M9 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS8-relay CN10-SDDB J7 for proper connection, and correct as necessary. 
  4. PS8 I/O check, sensor check SDDB J7-3 (ON) SD-511 6-G. 
  5. M9 operation check SDDB J11 11 to 20 SD-511 1 to 2-B. 
  6. Replace M9. 7 Replace SDDB. 8 Replace FSCB.

  • Code: C1132

Description:

Punch drive motor’s malfunction

<When FS-533+PK-519 is installed>

• The puncher drive cam sensor (PS203) or puncher home sensor (PS204) is not blocked or unblocked even after the set period of time has elapsed while the punch motor (M201) is energized.

• The punch motor sensor (PS202) does not turn ON after the punch motor (M201) stopped.

• The holes with other marketing area is set in [Service Mode] - [Finisher] - [Punch Option Setting]

<When FS-534+PK-520 is installed>

The punch home sensor (PS1) is not blocked or unblocked even after the set period of time has elapsed while the punch drive motor (M1) is energized.

Remedy:

When FS-533+PK-519 is installed:

  1. Check the number of the holes in [Service Mode] - [Finisher] - [Punch Option Setting]. 
  2. Check the connector between M201-PKCB CN203 for proper connection, and correct as necessary. 
  3. Check the connector of M201 for proper drive coupling, and correct as necessary. 
  4. Check the connector between PS202-PKCB CN204 for proper connection, and correct as necessary. 
  5. Check the connector between PS203-PKCB CN204. for proper connection, and correct as necessary. 
  6. Check the connector between PS204-PKCB CN204 for proper connection, and correct as necessary. 
  7. PS202 I/O check, sensor check PKCB CN204 FS-533 (PK-519) 5-C. 
  8. PS203 I/O check, sensor check PKCB CN204 FS-533 (PK-519) 6-C.
  9. PS204 I/O check, sensor check PKCB CN204 FS-533 (PK-519) 6-C. 
  10. M201 operation check PKCB CN203-1 to 2 FS-533 (PK-519) 4-C. 
  11. Replace M201. 
  12. PKCB F201 conduction check. 
  13. Replace PKCB. 
  14. Replace FSCB.

When FS-534+PK-520 is installed:

  1. Check the connector between M1-relay CN351-FSCB J7 for proper connection, and correct as necessary. 
  2. Check the connector of M1 for proper drive coupling, and correct as necessary. 
  3. Check the connector between PS1-FSCB J7 for proper connection, and correct as necessary. 
  4. PS1 I/O check, sensor check FSCB J7-5 (ON) FS-534 (PK-520) 7-K.
  5. M1 operation check FSCB J7 7 to 8 FS-534 (PK-520) 7-K 
  6. Replace M1. 
  7. Replace FSCB.

 

  • Code: C1140

Description:

Alignment plate motor/Rr’s malfunction

<When FS-533 is installed>

• The alignment plate home sensor/R (PS109) is not unblocked after the set period of time has elapsed after the plate drive starts from the home position.

• The alignment plate home sensor/R (PS109) is not blocked after the set period of time has elapsed when the plate returns to the home position.

<When FS-534 is installed>

The alignment plate/R home sensor (PS13) is not blocked or unblocked even after the set period of time has elapsed while the alignment motor/Rr (M8) is energized.

Remedy:

When FS-533 is installed:

  1. Check the connector between M106-FSCB CN102 for proper connection and correct as necessary.
  2. Check the connector of M106 for proper drive coupling and correct as necessary.
  3. Check the connector between PS109-relay CN106- FSCB CN102 for proper connection and correct as necessary.
  4. PS109 I/O check, sensor check FSCB CN102 FS-533 7-J
  5. M106 operation check FSCB CN102 FS-533 8-J
  6. Replace M106.
  7. FSCB CP105 conduction check.
  8. Replace FSCB.

When FS-534 is installed:

  1. Check the connector between M8-FSCB J12 for proper connection, and correct as necessary.
  2. Check the connector of M8 for proper drive coupling, and correct as necessary.
  3. Check the connector between PS13-FSCB J9 for proper connection, and correct as necessary.
  4. PS13 I/O check, sensor check FSCB J9<B>-9 (ON) FS-534 9-C.
  5. M8 operation check FSCB J12-13 to 16 FS-534 5~6-C to D
  6. Replace M8.
  7. Replace FSCB.